Kiln project done

Status
Not open for further replies.

Chrism

Well-Known Member
Joined
Jul 20, 2011
Messages
63
Points
0
Location
Oklahoma
Testing full thing tomorrow.. Just finished it. Sensor is on side inside of fridge, crockpot, and fan. Controller box is on outside displaying temp and Rh. Drilled 1" lower hole for fresh air. Up top I have another for the exhaust. Once up to temp the relay that's normally closed opens (basically shuts off crockpot at 120). This is sensed by the sensor I have inside reading it's values from the arduino that's in the black box.

4019aefe.jpg


4cd78e0a.jpg
 

Chrism

Well-Known Member
Joined
Jul 20, 2011
Messages
63
Points
0
Location
Oklahoma
Power supply on top of controller box is from a nintendo gamecube. The knob on bottom controls fan speed.
 

Chrism

Well-Known Member
Joined
Jul 20, 2011
Messages
63
Points
0
Location
Oklahoma
I used aluminum foil tape to seal my possible leaks. Expensive but works.
 

Chicken

redneck grower
Founding Member
Joined
Aug 28, 2011
Messages
4,631
Points
83
Location
FLORIDA
I used aluminum foil tape to seal my possible leaks. Expensive but works.

i used the same tape,,,, the duct tape is just for something i may have missed,,, the inside walls are lined with aluminum tape,
 

BarG

Founding Member
Joined
Jun 23, 2011
Messages
5,120
Points
113
Location
Texas, Brazos Vally
chrism, looks cool and a lot of tech.,just out of curiosity, what do you mean leaks, you need air circulation, and vent hole and assuming the old fridge has halfway decent gaskets what are you referring to.
 

Chrism

Well-Known Member
Joined
Jul 20, 2011
Messages
63
Points
0
Location
Oklahoma
I sealed any areas I had no control of because i wanted to make sure that heat is contained. When I gutted the fridge I had some areas exposing the insulating foam that I did not want. Fresh air comes in the bottom hole. Which the fans pulls some through. The hole on top is an exhaust. There is air circulating in a way. I don't want stale air. As I could be gone for a couple days... I believe as long as I can have the right humidity, temp, air circulation that'll make it basically hassle free. I may have to fluff the leafs in case excess moisture does collect on the leaf. It also helps control humidity having these. I'm working on a safer power plug as I have mentioned on htgt that having a double male extension cord is dangerous which I don't recommend. The extra outlet is going to be removed and the ac connections will be enclosed with a single male plug coming out that'll be connected to a household outlet.
Any comments or suggestions are appreciated.
 

BarG

Founding Member
Joined
Jun 23, 2011
Messages
5,120
Points
113
Location
Texas, Brazos Vally
I won't ask why you have a double male ext.cord :confused:, I'm still curious how you take an insulated enclosed unit and expose insulation? I understand need for ventilation, but could you be more specific on what was gutted to cause problems.
 

Chrism

Well-Known Member
Joined
Jul 20, 2011
Messages
63
Points
0
Location
Oklahoma
It was a freezer/fridge with icemaker. Took out all that stuff. It also had a shoot where ice came out of.
 

Daniel

Banned
Joined
May 22, 2011
Messages
538
Points
0
Location
Nevada
Chrism, Any report on how it is working? I know in my area a kiln will not tolerate much if any outside ventilation. our air is simply to dry and with the 120 degree temp of the kiln you can watch the moister escape if it finds outside air.
I have not found any issue with there not being fresh air. as I said my problem has been getting the moist air to move around enough. I am not sure fresh air, or more accurately Oxygen is having that much to do with the aging process. the heat and humidity seem to be the two ingredients needed.
I have also had problems in my kiln with getting the moisture to spread out evenly. I have a fan in the top of it but not at the bottom. I will be firing mine up again soon though and will see if i can get the bugs worked out.

I really like the electronic controls. any thought on marketing those?

My Fridge. kiln came with an outlet already installed. made it nice and easy for plugging in the crock pot.
 

Chrism

Well-Known Member
Joined
Jul 20, 2011
Messages
63
Points
0
Location
Oklahoma
I worked on the plug last night. It's more safe.
d21553e6.jpg

I'm pretty much done with it. Other than I want to set the heat automatically with buttons. Which I'll do later on. If I were to market it, I'd have a pcb manufactured for the unit. Or just use a plain arduino. You still would have to wire things up like a crockpot and the sensor. I'd have a bigger controller box to house the power supply (7-12v what's recommended on arduino). There would be a plug for the device coming out of it and a plug going to a wall outlet. This controller can be used for a wide variety of things as long as the power requirements are met. You don't want to run anything rated higher in amperage than what's attended for (lower the requirement the better).
I'd run another fan on the bottom. As long as air is circulated... When I built my forge a long while back I positioned the burners (I only needed one but ran 2) so that the flame would make a twirling circulation so heat would be evenly distributed on the metal I was heating up. I had a blast with this thing. Made my own tongs, knifes out of railroad spikes, some decorative stuff.
 

Jitterbugdude

Moderator
Founding Member
Joined
May 22, 2011
Messages
4,266
Points
113
Location
Northeast Maryland

deluxestogie

Administrator
Staff member
Joined
May 25, 2011
Messages
26,609
Points
113
Location
near Blacksburg, VA
How about a USB interface accessible on the exterior of the box, and a smart phone app that can be used to set parameters? This would take the place of hard-wired buttons.

Maybe even a USB wireless radio that could connect to your home Internet router/modem. Then you could set it or monitor it from the Ukraine or Tehran.

Bob
 

Chrism

Well-Known Member
Joined
Jul 20, 2011
Messages
63
Points
0
Location
Oklahoma
Wifi, Ethernet, Bluetooth... You could do any 3. I don't know if the ranco reads humidity? If not this is an advantage. I could used a more accurate sensor but it costs more. Main advantage: fun to build, learn about microcontrollers, learn how a relay works, plenty of support on any project you'd want as long as you got enough memory for the ic. A really bare minimum cost breakdown would be:
Arduino - 30.00
Relay - 5.00
Sensor - 15.00
That's 50 bucks. The rest you could salvage.... For me I bought the rest except fridge.
 
Status
Not open for further replies.
Top