Smashing Stems?

Status
Not open for further replies.

toomanymatoes

Active Member
Joined
Mar 24, 2022
Messages
25
Points
13
Location
Ontario, Canada
I am currently trying to educate myself on the various forms of curing and fermenting. I came across one video where the person smashed the tobacco leaf stems with a mallet prior to tying them into hands and hanging them. I have not seen anyone else do this or mention it. Since a lot of the moisture is retained in the stems, it seemed like it could be a good idea. However, I imagine choosing to do this or not has to do with the local RH, but am not really sure. Leaving the stems intact may help keeping the humidity at an appropriate level allowing for the desired gradual curing or in some cases make it worse by providing a good humid location for mold to grow.

Anyone know much about this approach?

edit: I found a post discussing this. I should have searched first.
 

deluxestogie

Administrator
Staff member
Joined
May 25, 2011
Messages
26,611
Points
113
Location
near Blacksburg, VA
I would simply point out that leaf is not normally tied in hands prior to curing. Tying green leaf into hands can lead to barn rot and mold. Complete the air-curing, then tie hands, if you like. There is no purpose, beyond the lovely aesthetics of a well-tied hand, for a home grower to ever need to tie leaf into hands.

Individual (primed) leaves can quickly be strung onto twine or (as I prefer) wire, for hanging in a curing shed. The leaves of my stalk-harvested plants remain on the stalk. Those stalks are hung in the shed, until their leaves are fully cured. Then the leaves are stripped and bagged for kilning (fermenting).

Bob
 

toomanymatoes

Active Member
Joined
Mar 24, 2022
Messages
25
Points
13
Location
Ontario, Canada
I would simply point out that leaf is not normally tied in hands prior to curing. Tying green leaf into hands can lead to barn rot and mold. Complete the air-curing, then tie hands, if you like. There is no purpose, beyond the lovely aesthetics of a well-tied hand, for a home grower to ever need to tie leaf into hands.

Individual (primed) leaves can quickly be strung onto twine or (as I prefer) wire, for hanging in a curing shed. The leaves of my stalk-harvested plants remain on the stalk. Those stalks are hung in the shed, until their leaves are fully cured. Then the leaves are stripped and bagged for kilning (fermenting).

Bob
I may be remembering wrong and the person did not actually bunch them into hands, but I believe he made bunches of 5 or 6 leaves. I have to find the video again.

I assumed it would be better to keep the leaves separate or in pairs for color curing. I watched another video where they weaved the individual leaves in-between two strands of twine. Somewhat like a Florida-weave used to support tomato plants. That made more sense to me, but still trying to learn the processes.

For stalk-harvested plants, is that based on the variety? I saw this being done for shorter plants.
 

Knucklehead

Moderator
Founding Member
Joined
Oct 18, 2012
Messages
12,777
Points
113
Location
NE Alabama

Curing, Fermentation, Aging, Kilning? Basic Definitions​

 

ChinaVoodoo

Moderator
Joined
Sep 1, 2014
Messages
7,220
Points
113
Location
Edmonton, AB, CA
I have cured in hands a couple times and I think this is a good idea (if you're going to cure in hands) because the stems shrink as they dry and the tie gets loose and leaves fall out, which is unfortunate sometimes because they are dry and then the leaves break.

Although, I think it was @Knucklehead who suggested rubber bands as a solution, which would also work.
 
Last edited:

ChinaVoodoo

Moderator
Joined
Sep 1, 2014
Messages
7,220
Points
113
Location
Edmonton, AB, CA
There is no purpose, beyond the lovely aesthetics of a well-tied hand, for a home grower to ever need to tie leaf into hands.
Space, convenience, reducing the drying rate. It worked really well for sun curing yellowed Japan 8 on my balcony. It also worked really well for finishing the drying of fire cured hands indoors where its ≈ 10% humidity. I'm against it for air curing. I got mold that way. I would recommend it for outdoor sun curing, or doing a final non-curing-shed dry in a climate like mine where the humidity is low enough that it's not going to mold.

I saw a photo once of tobacco hung in bundles of about 50lbs—also outside, and I believe in Israel.
 

Knucklehead

Moderator
Founding Member
Joined
Oct 18, 2012
Messages
12,777
Points
113
Location
NE Alabama
My humidity swings up and down during curing. I string my primed leaves so that I can bunch them together during periods of low humidity to help prevent drying green, then a few days later I may have to spread them back apart and turn on a shop fan for circulation to prevent rot. I have to keep an eye on the weather forecast, watch my current temp and humidity and adjust as necessary when the weather changes. I may have to close the shop doors before rain to keep humidity out, open the door during the day and close the door at night, or vise versa depending on whether I need to trap humidity inside or keep it out and turn on the fan until the weather changes. Some of the lucky guys on here can just hang their leaf up and forget about for a year or more, I'm not one of them. I have to monitor the leaf until cured, constantly change my micro environment, then get it inside in a controlled environment so it doesn't rot or mold. I don't worry about cured leaf drying out, I can always mist the bags with moisture and the aging continues. If I tried to cure green leaf in hands in my area it would rot without question. It just depends on where you live.
I previously tied my cured leaf in hands to kiln and then store, but since I store in bags there's no real reason to do so, it just adds another step when you are ready to use the tobacco. It does look cool.
 

deluxestogie

Administrator
Staff member
Joined
May 25, 2011
Messages
26,611
Points
113
Location
near Blacksburg, VA
Garden20150705_1882_Bob_longRedHand_400.jpg


Tied hands of cured tobacco look wonderful, and overflow with tradition, as they hark to the idealized past. For today's commercial growers, it's just no longer done.

Bob
 
Status
Not open for further replies.
Top