Which Injector?

Status
Not open for further replies.

Brown Thumb

Well-Known Member
Joined
May 4, 2012
Messages
4,060
Points
113
Location
Pa
The cabinet probably got smashed down in shipping and won't let the drawer slide out. Probably have to pry it out.
 

Gmac

Well-Known Member
Joined
Nov 15, 2014
Messages
200
Points
18
Location
Central Mississippi
With Mine you have to let the front end down, get it aligned, wiggle it, then lift it up level and slam it closed. it has a sensor that won't let it come on if it's ajar the least bit, so does the feeder where you put the tobacco in. I take the funnel off when I'm shredding whole leaf so it feeds real fast by starting it from the ends of the leaf. It makes long shreds with the whole leaf. Then I shred it again with the funnel on. I have a large stainless steel bowl about 18 or twenty inches diameter that I put a bar b que round in (got at dollar general in the Bar B Que section) It looks like a 16 inch round silver hardware cloth that you use to keep small objects from falling through the grill. I sift the shredded tobacco into the bowl, which leaves the big pieces on the screen. I used to buy threshed tobacco that had small stems in it, so I envented a way to get them smaller. Then I put it in a Sterilite canester(also at the General) to keep it fresh until I roll it. I pour what I'm going to use on a commercial 1/2 cookie sheet(available at Sam's or Hotel resturant supply for about $5.00) I comes into case a lot faster spread out thin like that. Then I scoop some into a large coolwhip container to fill the hopper on my injector. Remember for shredding 18-20 percent moisture if too much moisture will gum up the shredder. When My shredder first came the grease from the cogs had gotten on the knives of the shredder, made the tobacco tase like grease. So I took it completely apart and cleaned it with 90% alcohol, que tips, and run some white typing paper through also.

Also as I'm putting my shredded tobacco in the coolwhip box the last bit has a lot dust in it so I sift the dust out with a hand sifter into to a bowel and give it to the fireants it may not kill them but gives them a new experience in Life.
REMEMBER 14 % Moisture for injecting.
Here is the link for the first video from fresh choice: https://www.youtube.com/watch?v=payD3FPTsxE

I have all ten in a file on my computer, if you would like a DVD of them just PM me an address and I will Mail you one.
I hope this helps, feel free to ask questions. [ You know what Willie P. says, "hit don never hurts to ask."

Gmac
 
Last edited:

Boboro

Well-Known Member
Joined
Sep 5, 2011
Messages
4,530
Points
83
Location
Wren Mississippi
The whole back side of the motor/ cutter case was broke and it was hangin down. :( Its preaty much junk.
 

Boboro

Well-Known Member
Joined
Sep 5, 2011
Messages
4,530
Points
83
Location
Wren Mississippi
I got it from a member here. It could have happened in shippin.I guess Ill eat it. I can still make it work but cant resell it.
 

Boboro

Well-Known Member
Joined
Sep 5, 2011
Messages
4,530
Points
83
Location
Wren Mississippi
The stuffer works well. It needs a nozzle. Do I replace it by takein the 2 screws on the frount of the machine off or do I have to do it from in side.
 

Gmac

Well-Known Member
Joined
Nov 15, 2014
Messages
200
Points
18
Location
Central Mississippi
Are you talking about the tube valve that you put the tube on behind the black and white round plate or the spoon.
If it's the tube valve there are two 1/16 allen screws that hold it on. Is it broken? Do you need parts. If so I can send you a phone #. Be sure to watch the videos and you will be able to take it completely apart and clean and adjust as needed.

Gmac
 

Boboro

Well-Known Member
Joined
Sep 5, 2011
Messages
4,530
Points
83
Location
Wren Mississippi
Yea... the tube valve. I have one one the other machine. Its split. But I will need to send off the broke machine. A number would be great.
 

Gmac

Well-Known Member
Joined
Nov 15, 2014
Messages
200
Points
18
Location
Central Mississippi
1-800-243-2737-----707-759-2506 After 11:00 O'clock AM central time.


Ask to speak to Jeff or Logan.


Gmac
 

IanA2

Well-Known Member
Joined
May 20, 2014
Messages
51
Points
0
Location
UK
Turn it on. Ih has two probes. Grab a handful of shreded tobacco stick the probes into the tobacco it gives a digital reading. 14% is perfect for use in an injector. 18-20 % for storage works well for me, as well as shredding. Too much moisture rolling or shredding wrecks your equipment.

Roll on,
Gmac
Thanks.
 

BarG

Founding Member
Joined
Jun 23, 2011
Messages
5,120
Points
113
Location
Texas, Brazos Vally
Let us know if it works. I've never tried an auger type injector because of all of the bad publicity they get, but you might have found a good one.
All the reviews I researched prior to buying the powermatic indicated that the cherrys would fall in your lap. It will grind your tobacco especialy in low case.
 

Boboro

Well-Known Member
Joined
Sep 5, 2011
Messages
4,530
Points
83
Location
Wren Mississippi
Yea.. It was a lot of cash an will have to send one of the injectors off. But I had been wantin one for a while. I may sell the Power matic shredder an one of the injectors.
 

IanA2

Well-Known Member
Joined
May 20, 2014
Messages
51
Points
0
Location
UK
UPDATE

Well I've finally sorted out my PM II and it's working fine. I took it apart and discovered that the problem was that the plastic part that round down the two metal rods was not running smoothly. In fact sticking, not really sure why, but with a bit of jiggling and lubrication it's now going fine. Would I buy another? Well maybe, but not from the US. Zico's approach was not exactly up to the CS standards we see in EU (and believe me that ain't too good), so if they were on sale in UK/EU I probably would. It's essentially a good bit of kit let down by poor ownership by the manufacturer, at least on this side of the pond!
 

DGBAMA

Well-Known Member
Joined
Feb 10, 2013
Messages
4,418
Points
63
Location
NORTH ALABAMA
After 2 years of faithful service, I took mine apart for cleaning tonight. Quite a pile of dust inside. Hope I get another 2 years. Between 4 smokers I know it has made near 200 cartons.14206872333420.jpg
 

Gmac

Well-Known Member
Joined
Nov 15, 2014
Messages
200
Points
18
Location
Central Mississippi
I clean mine once a month. I also sift the dust out of my tobacco before I Put it in the injector.
I figure dust is not good for electric motors or moving parts.

Gmac
 

burge

Well-Known Member
Joined
Apr 11, 2014
Messages
1,705
Points
113
Location
Alberta
I have the excell and the premier supermatic both are really good out of the ones mentioned I prefer the excell
 

Nesikep

Member
Joined
Jan 22, 2015
Messages
18
Points
0
Location
Lillooet, British Columbia, Canada
I have been rolling with the same Laramie manual pocket injector for about 5 years.. I've had to epoxy the lid hinge a couple times, as well as other parts, but for $5 it's served me well.. it has just a little bit longer a stroke than the Rizzla and various others, which makes it stuff a full smoke.. Depending on the tube it may tear a bit off the end. If I could find some more new ones I'd stock up on them, but no luck anymore here. If my tobacco is right I can do about 4-5 per minute.. if I don't mangle the end of the tube *Grr*
 

chillardbee

Well-Known Member
Joined
May 29, 2013
Messages
888
Points
63
Location
Chilliwack BC, Canada (south western Canada)
attachment.php


Just ordered this little machine to expediate the rolling proccess.

I tried this machine and I'm sorry to say that it's a piece of $h!t. The motor cuts out if over heated and it over heats about 2-3 times per cig even using very dry baccy. Takes about 8 minutes to roll a cig. My old style injector, since I cleaned it pumps out a cig every 30 - 45 seconds.
 
Status
Not open for further replies.
Top